Quartz crystal microbalance-based aptasensor integrated with magnetic pre-concentration system for detection of Listeria monocytogenes in food samples.

A fast and accurate identification of Listeria monocytogenes. A new quartz crystal microbalance (QCM) aptasensor was designed for the specific and rapid detection of L. monocytogenes. Before detection of the target bacterium from samples in the QCM aptasensor, a magnetic pre-enrichment system was used to eliminate any contaminant in the samples. The prepared magnetic system was characterized using ATR-FTIR, SEM, VSM, BET, and analytical methods. The saturation magnetization values of the Fe3O4, Fe3O4@PDA, and Fe3O4@PDA@DAPEG particles were 57.2, 40.8, and 36.4 emu/g, respectively. The same aptamer was also immobilized on the QCM crystal integrated into QCM flow cell and utilized to quantitatively detect L. monocytogenes cells from the samples. It was found that a specific aptamer-magnetic pre-concentration system efficiently captured L. monocytogenes cells in a short time (approximately 10 min). The Fe3O4@PDA@DA-PEG-Apt particles provided selective isolation of L. monocytogenes from the bacteria-spiked media up to 91.8%. The immobilized aptamer content of the magnetic particles was 5834 µg/g using 500 ng Apt/mL. The QCM aptasensor showed a very high range of analytical performance to the target bacterium from 1.0 × 102 and 1.0 × 107 CFU/mL. The limit of detection (LOD) and limit of quantitation (LOQ) were 148 and 448 CFU/mL, respectively, from the feeding of the QCM aptasensor flow cell with the eluent of the magnetic pre-concentration system. The reproducibility of the aptasensor was more than 95%. The aptasensor was very specific to L. monocytogenes compared to the other Listeria species (i.e., L. ivanovii, L. innocua, and L. seeligeri) or other tested bacteria such as Staphylococcus aureus, Escherichia coli, and Bacillus subtilis. The QCM aptasensor was regenerated with NaOH solution, and the system was reused many times.

Tramates trogii biomass in carboxymethylcellulose-lignin composite beads for adsorption and biodegradation of bisphenol A.

Tramates trogii biomass was immobilized in carboxymethyl cellulose-lignin composite beads via cross-linking with Fe(III) ions (i.e., Fe(III)-CMC@Lig(1-4)@FB). The composite beads formulations were used for the adsorption and degradation of bisphenol A (BPA) using the free fungal biomass as a control system. The maximum adsorption capacity of the free fungal biomass and Fe(III)-CMC@Lig-3@FB for BPA was found to be 57.8 and 95.6, mg/g, respectively. The degradation rates of BPA were found to be 87.8 and 89.6% for the free fungal biomass and Fe(III)CMC@Lig-3@FB for 72 h in a batch reactor, respectively. Adsorption of BPA on the free fungal biomass and Fe(III)CMC@Lig-3@FB fungal preparations described by the Langmuir and Temkin isotherm models, and the pseudo-second-order kinetic model. The values of Gibbs free energy of adsorption (ΔG°) were - 20.7 and - 25.8 kJ/mol at 298 K for BPA on the free fungal biomass and Fe(III)-CMC@Lig-3@FB beads, respectively. Moreover, the toxicities of the BPA and degradation products were evaluated with three different test organisms: (i) a freshwater micro-crustacean (Daphnia magna), (ii) a freshwater algae (Chlamydomonas reinhardti), and (iii) a Turkish winter wheat seed (Triticum aestivum L.). After treatment with the Fe(III)CMC@Lig-3@FB formulation, the degradation products had not any significant toxic effect compared to pure BPA. This work shows that the prepared composite bioactive system had a high potential for degradation of BPA from an aqueous medium without producing toxic end-products. Thus, it could be a good candidate for environmentally safe biological methods.

Modification of epoxy groups of poly(hydroxylmethyl methacrylate-co-glycidyl methacrylate) cryogel with H3PO4 as adsorbent for removal of hazardous pollutants.

Poly(hydroxylmethyl methacrylate-co-glycidyl methacrylate) (p(HEMA-GMA)) macroporous cryogel with high density of epoxy groups was synthesized, and the epoxy groups of the cryogel were modified into phosphonate groups. The effects of dye concentrations, adsorption time, pH, salt concentration, and adsorption temperature on the adsorption of Direct Blue-53 (DB-53) and Reactive Blue-160 (RB-160) dyes were studied. The maximum adsorption capacity was found to be 245.3 and 155.8 mg/g (0.255 or 0.119 mmol/g) for the DB-53 and RB-160 dyes, respectively. The higher adsorption capacity achieved for the DB-53 compared with the RB-160 dye can result from the pendant primary amino groups of the DB-53 dye as well as the smaller size of the dye molecule. The Langmuir isotherm model and the pseudo-second-order kinetic model well described the experimental data. The p(HEMA-GMA)-PO42- adsorbent has many operational advantages for the removal of pollutants. It could be a promising adsorbent to be used in industrial wastewater treatment.

Poly (hydroxyethyl methacrylate-glycidyl methacrylate) films modified with different functional groups: In vitro interactions with platelets and rat stem cells.

Copolymerization of 2-hydroxyethylmethacrylate (HEMA) with glycidylmethacrylate (GMA) in the presence of α-α'-azoisobisbutyronitrile (AIBN) resulted in the formation of hydrogel films carrying reactive epoxy groups. Thirteen kinds of different molecules with pendant NH2 group were used for modifications of the p(HEMA-GMA) films. The NH2 group served as anchor binding site for immobilization of functional groups on the hydrogel film via direct epoxy ring opening reaction. The modified hydrogel films were characterized by FTIR, and contact angle studies. In addition, mechanical properties of the hydrogel films were studied, and modified hydrogel films showed improved mechanical properties compared with the non-modified film, but they are less elastic than the non-modified film. The biological activities of these films such as platelet adhesion, red blood cells hemolysis, and swelling behavior were studied. The effect of modified hydrogel films, including NH2, (using different aliphatic CH2 chain lengths) CH3, SO3H, aromatic groups with substituted OH and COOH groups, and amino acids were also investigated on the adhesion, morphology and survival of rat mesenchymal stem cells (MSCs). The MTT colorimetric assay reveals that the p(HEMA-GMA)-GA-AB, p(HEMA-GMA)-GA-Phe, p(HEMA-GMA)-GA-Trp, p(HEMA-GMA)-GA-Glu formulations have an excellent biocompatibility to promote the cell adhesion and growth. We anticipate that the fabricated p(HEMA-GMA) based hydrogel films with controllable surface chemistry and good stable swelling ratio may find extensive applications in future development of tissue engineering scaffold materials, and in various biotechnological areas.